- Subjects
- Design Technology
- Question bank
- B4.1 Production systems
B4.1 Production systems questions for IB Design Technology
96 questions on Production systems, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.
- IB Design Technology
- Part of B Design in practice
- HL only
Questions by paper and level
| Paper | Questions |
|---|---|
| Paper 1 | 39 |
| Paper 2 | 57 |
| Every paper | 96 |
Counted on
Questions to try
Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.
A firm can make a nylon clip by selective laser sintering (SLS) for €16 per clip at any quantity, or by injection molding, which needs a €9,000 mold and then costs €1 per clip. Figure 1 shows the cost per clip of each technique against the number of clips made.

Above about how many clips does injection molding give the lower cost per clip?
The Gristwell pepper mill has a central spindle made from 6 mm diameter 316 stainless steel bar. The spindles are made on a CNC lathe in batches of 5000. One end of the bar is turned down to a smaller diameter, a thread is cut on the other end, and each spindle is then parted off to length.
- (a)
State the category of manufacturing technique to which turning the Gristwell spindle belongs.
1 mark
- (b)
Describe how turning reduces the diameter of one end of the Gristwell spindle.
2 marks
- (c)
Outline one reason why the Gristwell spindle is turned on a CNC lathe rather than a manually operated lathe.
2 marks
A production system in which skilled workers make each product mainly by hand, using hand tools and a few general-purpose machines, is known as…
The Peakview action camera is sold in a waterproof housing for divers. The housing is machined from a solid block of 6061 aluminum alloy on a three-axis CNC milling machine, in batches of about 2000 a year. Most of the block is removed as swarf. After milling, the housing is bead blasted (sprayed with fine glass beads) and then anodized black. The table shows the mass of one housing at each stage of milling.
Stage | Mass / g |
|---|---|
Block of aluminum before milling (80 × 60 × 40 mm) | 518 |
After rough milling | 142 |
Finished housing after final milling | 86 |
- (a)
State the mass of aluminum removed from one Peakview housing during final milling.
1 mark
- (b)
Calculate the percentage of the original block's mass that is removed to make one finished Peakview housing. Show your working.
2 marks
- (c)
Describe how milling removes material from the aluminum block to form the Peakview housing.
2 marks
- (d)
Outline one way the swarf from milling the Peakview housings can be prevented from becoming waste.
2 marks
- (e)
Explain one reason why the Peakview housing is milled from solid rather than die cast.
3 marks
- (f)
Explain two reasons why the milled Peakview housing is bead blasted and then anodized.
6 marks
Which of the following best describes mechanized production?
The Rondo café chair has a frame made from 22 mm diameter mild steel tube. Each frame is bent from two long lengths of tube on a CNC tube-bending machine, and the two lengths are then MIG welded together. The frame is powder coated, and an injection-molded polypropylene seat is fastened to it with four screws. Rondo chairs are made in batches of 500 for restaurants with outdoor terraces.
- (a)
State one property of mild steel that allows the Rondo frame to be bent without cracking.
1 mark
- (b)
Describe how the tube for the Rondo frame is bent on the tube-bending machine.
2 marks
- (c)
Outline one advantage of bending the Rondo frame from long lengths of tube rather than welding it from many short straight pieces.
2 marks
- (d)
Explain one reason why the seat of the Rondo chair is fastened to the frame with screws rather than adhered.
3 marks
- (e)
Explain two ways in which powder coating enhances the Rondo chair frame.
6 marks
Practice all 96 in Augment
Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.
More questions in Design in practice
- B1.1User-centred design
- B2.1The design process
- B2.2Modelling and prototyping
- B3.1Material selection
- B3.2Structural systems application and selection
- B3.3Mechanical systems application and selection
- B3.4Electronic systems application and selection
- B4.1Production systemsThis page
Check your answers in Augment
A free account opens all 96 questions on Production systems with their markschemes, and keeps a record of what you have marked.