B2.2 Modelling and prototyping questions for IB Design Technology

150 questions on Modelling and prototyping, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of B Design in practice
  • SL and HL

Questions by paper and level

SL and HL questions are for students at either level. HL only questions cover what only HL students study.

PaperSL and HLHL onlyAll
Paper 167875
Paper 2502575
Every paper11733150

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00109Paper 1 · 1 mark

Figure 1 shows a drawing of a desk stand for a tablet computer.

Line drawing of an L-shaped stand shown as one assembled three-dimensional view: vertical edges are drawn upright and the horizontal edges run at equal angles of 30 degrees to the horizontal on both sides. There are no hidden lines and no separate views.
**Figure 1**

What type of drawing is shown in Figure 1?

  1. A

    Isometric drawing

  2. B

    Orthographic projection

  3. C

    Exploded drawing

  4. D

    Free-hand sketch

Question 2 · DT-00455Paper 2 · HL only · 6 marks

An architecture practice builds massing models of proposed buildings on a laminated object manufacture (LOM) machine. The machine bonds sheets of adhesive-coated paper together and cuts each sheet with a blade. The finished models look and feel similar to wood and can be up to 300 mm tall.

  1. (a)

    Outline how the LOM machine produces one layer of a massing model.

    2 marks

  2. (b)

    Explain one advantage of LOM for producing the architecture practice's massing models.

    3 marks

  3. (c)

    State one limitation of the LOM massing models for the architecture practice.

    1 mark

Question 3 · DT-00110Paper 1 · 1 mark

Figure 2 shows a drawing from the repair instructions for a handheld flashlight. Each part is drawn separated from the others along a common center line.

Drawing of the parts of a cylindrical flashlight laid out in a row along a dashed center line, with gaps between them: front bezel ring, lens disc, cone-shaped reflector, long body tube, battery, spring and end cap.
**Figure 2**

What is the main reason this type of drawing is used in the instructions?

  1. A

    It gives the exact dimensions of each part

  2. B

    It shows the material each part is made from

  3. C

    It shows how the parts fit together and in what order

  4. D

    It shows how the flashlight looks in use

Question 4 · DT-00456Paper 2 · HL only · 6 marks

Beamo, a small start-up, has designed a handlebar bracket for a bicycle light. Early versions of the bracket were printed in PLA on a fused deposition modeling (FDM) printer to check its size and how it clips onto different handlebars. The 600 brackets sold in the first year are made in nylon (PA12) by selective laser sintering (SLS).

  1. (a)

    State what is meant by rapid prototyping, as used in the development of the Beamo bracket.

    1 mark

  2. (b)

    Outline one reason why FDM in PLA was suitable for the initial base models of the Beamo bracket.

    2 marks

  3. (c)

    Explain why SLS in nylon, rather than FDM, is used to produce the refined brackets sold to customers.

    3 marks

Question 5 · DT-00114Paper 1 · 1 mark

Figure 3 shows a drawing of a mounting bracket for a door handle. Dimensions are in mm.

Three flat views of an L-shaped bracket: a plan at the top left, a front view at the bottom left showing the L shape, 80 long and 50 high, and a side view at the bottom right, 40 wide, with a 10 mm diameter hole. Hidden edges of the hole are dashed.
**Figure 3**

At which stage of design development is this type of drawing mainly used?

  1. A

    Communicating final details for manufacture

  2. B

    Generating first ideas for the bracket

  3. C

    Gathering users' opinions of its appearance

  4. D

    Testing how the bracket performs under load

Question 6 · DT-00461Paper 2 · HL only · 6 marks

A toy company is developing a range of 80 mm tall action figures that will be injection molded in ABS in runs of 200,000. Before the steel molds are ordered, the designers print base models of each figure on an FDM printer. A limited-edition version of each figure, 500 of each, is made directly by stereolithography (SLA) in a tough production resin.

  1. (a)

    Outline the difference between a base model and a refined product made by additive techniques, as used for the action figures.

    2 marks

  2. (b)

    State one additive technique, other than SLA, that could be used to produce refined products such as the limited-edition figures in low volumes.

    1 mark

  3. (c)

    Explain why the FDM base models of the figures cannot be used to show how strong the injection-molded ABS figures will be.

    3 marks

Practice all 150 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in practice

  1. B1.1User-centred design
  2. B2.1The design process
  3. B2.2Modelling and prototypingThis page
  4. B3.1Material selection
  5. B3.2Structural systems application and selectionHL only
  6. B3.3Mechanical systems application and selectionHL only
  7. B3.4Electronic systems application and selectionHL only
  8. B4.1Production systemsHL only

Check your answers in Augment

A free account opens all 150 questions on Modelling and prototyping with their markschemes, and keeps a record of what you have marked.