B3.2 Structural systems application and selection questions for IB Design Technology

74 questions on Structural systems application and selection, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of B Design in practice
  • HL only

Questions by paper and level

PaperQuestions
Paper 140
Paper 234
Every paper74

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00052Paper 1 · 1 mark

In a tensile test, a sample of an aluminum alloy carries a stress of 140 MPa at a strain of 0.002. The sample is still in its elastic region.

What is the Young's modulus of the alloy?

  1. A

    0.07 GPa

  2. B

    7 GPa

  3. C

    70 GPa

  4. D

    700 GPa

Question 2 · DT-00677Paper 2 · 14 marks

The Fold-Flat desk is a wall-mounted desk for small apartments. Its 700 mm deep birch plywood top is joined to a rail on the wall by a locking hinge that holds the top level when it is lowered. When the top is lowered, a steel strut on each side runs diagonally from the underside of the top to a bracket on the wall, see Figure 2. In testing, the desk failed when a load of 1500 N was placed on its front edge.

Side view of the Fold-Flat desk. A horizontal desk top is hinged to a wall at its left end. A strut runs diagonally from a wall bracket below the hinge up to the underside of the desk top near its front. A downward load acts at the front edge of the desk top.
Figure 2: side view of the Fold-Flat desk in use
  1. (a)

    Identify the type of beam the Fold-Flat desk top would act as if the struts were removed.

    1 mark

  2. (b)

    State the type of force in the strut when a load is placed on the Fold-Flat desk top.

    1 mark

  3. (c)

    The Fold-Flat desk failed when the 1500 N load was placed on its front edge. Outline why the same load placed close to the wall would be less likely to make the desk fail.

    2 marks

  4. (d)

    Outline how tension acts on the screws that fix the wall rail of the Fold-Flat desk to the wall when the front edge is loaded.

    2 marks

  5. (e)

    The designers want the Fold-Flat desk to have a safety factor of 3. Calculate the maximum load the desk should be expected to carry at its front edge.

    2 marks

  6. (f)

    Explain how the struts and the laminated structure of the birch plywood strengthen the Fold-Flat desk.

    6 marks

Question 3 · DT-00291Paper 1 · 1 mark

A team designing a delivery drone runs FEA on four CAD versions of a nylon motor arm under the same load. The nylon has a yield strength of 50 MPa, and the arm must have a safety factor of at least 2.0 based on yield.

Design

Maximum stress from FEA / MPa

Mass / g

W

31

18

X

26

20

Y

24

22

Z

19

27

Which is the lightest design that meets the requirement?

  1. A

    W

  2. B

    X

  3. C

    Y

  4. D

    Z

Question 4 · DT-00680Paper 2 · 15 marks

Altura is developing the Ascent trekking pole, which folds into three sections. The thin lower section takes the largest loads when a hiker leans on the pole or it becomes wedged between rocks. Two alloys are being considered for the lower section: an aluminum alloy (Material X) and a titanium alloy (Material Y). Figure 3 shows the results of tensile tests on samples of each material.

Stress-strain graph. X: straight from the origin to 450 MPa at 0.64 % strain, then curves up to a peak of 520 MPa at 6 % and falls to 500 MPa where it ends at 10 %. Y: straight to 880 MPa at 0.8 %, rises to a peak of 950 MPa at 7 %, ends at 915 MPa at 13 %.
Figure 3: tensile test results for Materials X and Y
  1. (a)

    State the ultimate tensile strength of Material Y.

    1 mark

  2. (b)

    State the yield strength of Material X.

    1 mark

  3. (c)

    State the strain at which Material X fractures.

    1 mark

  4. (d)

    Describe the relationship between stress and strain for Material X up to its yield strength.

    2 marks

  5. (e)

    A hiker leans on the Ascent pole so that a stress of 500 MPa acts in its lower section. Outline what happens to the lower section when it is made from Material X and when it is made from Material Y.

    2 marks

  6. (f)

    A sample of Material X is under a stress of 280 MPa and has a strain of 0.004. Calculate the Young's modulus of Material X.

    2 marks

  7. (g)

    Material Y has a higher Young's modulus and a higher yield strength than Material X. Explain how Young's modulus and yield strength would influence the choice of material for the lower section of the Ascent pole.

    6 marks

Question 5 · DT-00297Paper 1 · 1 mark

FEA of a steel footplate bracket for a wheelchair gives a maximum stress of 36 MPa. The steel has a yield strength of 90 MPa.

What is the safety factor of the bracket based on the FEA result?

  1. A

    0.40

  2. B

    2.5

  3. C

    54

  4. D

    126

Question 6 · DT-00694Paper 2 · 19 marks

Pacer builds custom racing wheelchairs for track athletes. The frame of its earlier T4 model was welded from aluminum alloy tubes. The frame of the new T5 is a single hollow shell of carbon-fiber-reinforced polymer (CFRP), laid up in layers with the fibers in different directions and cured in a mold. Table 3 shows the results of tests on both frames.

Property

T4 aluminum tube frame

T5 CFRP shell frame

Mass of frame / kg

4.2

2.6

Load at which frame failed in testing / N

6000

7200

Maximum load in use / N

1500

1800

Table 3: test results for the T4 and T5 frames

  1. (a)

    State the type of structure of the T5 frame.

    1 mark

  2. (b)

    Using Table 3, calculate the safety factor of the T5 frame.

    2 marks

  3. (c)

    Outline why the carbon fibers in the T5 frame are laid in layers with the fibers in different directions.

    2 marks

  4. (d)

    Outline why a high Young's modulus is desirable for the T5 frame.

    2 marks

  5. (e)

    Carbon-fiber-reinforced polymer shows almost no plastic deformation before it fractures, unlike aluminum alloy. Explain why a safety factor above 1 is especially important for the T5 frame.

    3 marks

  6. (f)

    Explain how structural performance, mass and end of life were affected by changing from the T4 aluminum tube frame to the T5 CFRP shell frame.

    9 marks

Practice all 74 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in practice

  1. B1.1User-centred design
  2. B2.1The design process
  3. B2.2Modelling and prototyping
  4. B3.1Material selection
  5. B3.2Structural systems application and selectionThis page
  6. B3.3Mechanical systems application and selection
  7. B3.4Electronic systems application and selection
  8. B4.1Production systems

Check your answers in Augment

A free account opens all 74 questions on Structural systems application and selection with their markschemes, and keeps a record of what you have marked.