- Subjects
- Design Technology
- Question bank
- B3.4 Electronic systems application and selection
B3.4 Electronic systems application and selection questions for IB Design Technology
87 questions on Electronic systems application and selection, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.
- IB Design Technology
- Part of B Design in practice
- HL only
Questions by paper and level
| Paper | Questions |
|---|---|
| Paper 1 | 40 |
| Paper 2 | 47 |
| Every paper | 87 |
Counted on
Questions to try
Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.
Figure 1 shows the circuit of a battery-powered cupboard light.

Which labeled component limits the current so that the LED is not damaged?
The Glide powered wheelchair is steered with a joystick on one armrest. The joystick contains two potentiometers whose output voltages vary with its forward–back and left–right position, and a microcontroller converts these into speeds for the two drive motors. Some Glide users have a hand tremor (involuntary shaking) or weak hand muscles. A carer can change the Glide's settings to alter how far the joystick must move for full speed, and to switch on a software filter that ignores rapid small movements. The joystick can also be moved to either armrest and forward or back along it.
- (a)
State whether the output of the potentiometers in the Glide joystick is an analogue or a digital signal.
1 mark
- (b)
Outline how a hand tremor affects a user's ability to steer the Glide wheelchair with a standard joystick.
2 marks
- (c)
Explain how the software filter in the microcontroller of the Glide wheelchair helps users with a hand tremor.
3 marks
- (d)
Outline one reason why the joystick of the Glide wheelchair can be moved to either armrest and along it.
2 marks
- (e)
Explain how muscle strength and fatigue were considered in the design of the joystick control of the Glide wheelchair.
6 marks
An electric toothbrush contains a rechargeable battery, a microcontroller, a drive motor that turns the brush head, a small vibration motor and an induction charging coil. Every 30 seconds the vibration motor gives a short pulse, telling the user to move to the next part of the mouth.
Which component times the 30-second intervals?
The Nuvo bottle warmer heats a baby's bottle of milk in a small bath of water. A parent places the bottle in the water, chooses "milk" or "thaw" with a push button and presses start. A temperature sensor in the water bath sends a signal to a microcontroller, which switches a relay on and off to control a 200 W heating plate so that the water stays at 40 °C. When the milk is ready a green LED lights and a buzzer sounds three times. The warmer runs from the mains and switches itself off after 30 minutes. Figure 1 shows a system diagram of the Nuvo bottle warmer.

- (a)
State the type of control system shown in Figure 1 for the Nuvo bottle warmer.
1 mark
- (b)
Identify two output devices of the Nuvo bottle warmer.
2 marks
- (c)
Outline the purpose of the path labeled Z in Figure 1 for the Nuvo bottle warmer.
2 marks
- (d)
Describe how the temperature sensor and microcontroller work together as the input and process stages of the Nuvo bottle warmer.
2 marks
- (e)
Explain why the Nuvo bottle warmer uses a relay to switch the heating plate.
3 marks
- (f)
Explain how the electronic system of the Nuvo bottle warmer addresses safety and energy use.
6 marks
A digital kitchen scale has a load cell, an operational amplifier (op-amp), a microcontroller, a liquid crystal display (LCD) and a push button that sets the reading to zero.
Which of the following are part of the process stage of the scale?
I. The op-amp that amplifies the small signal from the load cell
II. The microcontroller that converts the signal into a mass in grams
III. The LCD that shows the mass
The Spinwell exercise bike shows the rider's cadence and speed on an LCD screen on the handlebars. A small magnet is fixed to the edge of the bike's flywheel, and a coil sensor is fixed to the frame next to it. As the flywheel turns, the coil sensor produces an analogue voltage that rises and falls once for each revolution of the flywheel. The display unit contains signal-conditioning circuits and a microcontroller, and runs from four 1.5 V cells. During testing, an engineer connected the coil sensor to an oscilloscope while the flywheel turned at a steady speed. Figure 1 shows the trace.

- (a)
State the peak voltage of the signal from the Spinwell coil sensor shown in Figure 1.
1 mark
- (b)
State the period of one cycle of the signal in Figure 1, in seconds.
1 mark
- (c)
Calculate the frequency of the signal from the Spinwell coil sensor shown in Figure 1, using frequency = 1 / period.
2 marks
- (d)
Outline why the signal from the Spinwell coil sensor is described as analogue.
2 marks
- (e)
Explain why the signal from the coil sensor must pass through signal conditioning before the microcontroller in the Spinwell display unit can use it.
3 marks
- (f)
Explain how the choice of output device and the power supply affect the design of the Spinwell display unit.
6 marks
Practice all 87 in Augment
Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.
More questions in Design in practice
- B1.1User-centred design
- B2.1The design process
- B2.2Modelling and prototyping
- B3.1Material selection
- B3.2Structural systems application and selection
- B3.3Mechanical systems application and selection
- B3.4Electronic systems application and selectionThis page
- B4.1Production systems
Check your answers in Augment
A free account opens all 87 questions on Electronic systems application and selection with their markschemes, and keeps a record of what you have marked.