- Subjects
- Design Technology
- Question bank
- B3.3 Mechanical systems application and selection
B3.3 Mechanical systems application and selection questions for IB Design Technology
79 questions on Mechanical systems application and selection, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.
- IB Design Technology
- Part of B Design in practice
- HL only
Questions by paper and level
| Paper | Questions |
|---|---|
| Paper 1 | 37 |
| Paper 2 | 42 |
| Every paper | 79 |
Counted on
Questions to try
Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.
A wall-mounted bike hook is fixed by two screws, one 100 mm directly above the other. A bike weighing 200 N hangs from the hook 250 mm out from the wall. The hook plate tends to pivot about its bottom edge, which is level with the lower screw.
What tensile force must the top screw resist?
The Vela C8 is a commuter bicycle. The pedals turn a single chainring with 44 teeth, and a roller chain carries the drive to one of eight sprockets on the rear wheel, from 11 teeth (smallest) to 32 teeth (largest). A rear derailleur moves the chain from one sprocket to another when the rider changes gear. Its cage carries two small toothed jockey wheels that guide the chain and take up its slack. The chain must be cleaned and oiled regularly and is replaced when it has worn.
- (a)
Identify the driver and the driven component in the chain drive of the Vela C8.
2 marks
- (b)
Calculate the number of turns of the rear wheel of the Vela C8 for one turn of the pedals when the chain is on the 11-tooth sprocket.
2 marks
- (c)
Outline the function of the jockey wheels in the Vela C8.
2 marks
- (d)
Explain why a rider of the Vela C8 moves the chain onto the 32-tooth sprocket when climbing a steep hill.
3 marks
- (e)
Outline one reason why the Vela C8 uses a chain and sprockets rather than a smooth belt and pulleys.
2 marks
- (f)
Outline one reason why the output of the chain drive of the Vela C8 is less than the input from the rider.
2 marks
- (g)
Explain how the drive system of the Vela C8 supports sustainable commuting in terms of efficiency and maintenance.
6 marks
A chain block in a vehicle workshop lifts an engine weighing 1200 N when the mechanic pulls on the hand chain with a force of 160 N.
What is the mechanical advantage of the chain block?
The Kernel nutcracker has two steel arms hinged together at one end. A walnut is placed between the arms 30 mm from the hinge, and the user squeezes the free ends of the arms 150 mm from the hinge. In a test, a user applied an effort of 40 N and the nut cracked under a load of 200 N.
- (a)
Identify the class of lever formed by the Kernel nutcracker.
1 mark
- (b)
Calculate the mechanical advantage of the Kernel nutcracker in the test.
2 marks
- (c)
Outline why the walnut is placed close to the hinge of the Kernel nutcracker.
2 marks
- (d)
A fishing rod acts as a third class lever, with the effort applied between the fulcrum and the load. Outline why the designer of a fishing rod accepts a mechanical advantage of less than 1.
2 marks
In a hand-cranked grain mill, a 15-tooth gear on the crank shaft drives a 60-tooth gear on the grinding stone's shaft.
What is the velocity ratio of the gear pair, taking velocity ratio as driven teeth ÷ driver teeth?
Kinetic Health designs cable machines for physiotherapy clinics. Patients pull a handle on a steel cable to lift a stack of weight plates. Figure 1 shows two pulley arrangements the design team considered. In arrangement A the cable passes over one fixed pulley. In arrangement B one end of the cable is fixed to the frame, and the cable passes around a pulley attached to the weight stack and then over a fixed pulley to the handle.

- (a)
State the function of the fixed pulley in arrangement A of the Kinetic Health machine.
1 mark
- (b)
Identify the type of pulley attached to the weight stack in arrangement B.
1 mark
- (c)
Outline why a patient using arrangement A must pull with a force at least equal to the weight of the stack being lifted.
2 marks
- (d)
Explain how arrangement B changes the effort needed and the distance the handle moves, compared with arrangement A.
3 marks
- (e)
Outline one reason why the actual effort needed in arrangement B is more than half the weight of the stack.
2 marks
- (f)
Evaluate the use of arrangement B rather than arrangement A in a cable machine for older adults recovering from injury.
6 marks
Practice all 79 in Augment
Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.
More questions in Design in practice
- B1.1User-centred design
- B2.1The design process
- B2.2Modelling and prototyping
- B3.1Material selection
- B3.2Structural systems application and selection
- B3.3Mechanical systems application and selectionThis page
- B3.4Electronic systems application and selection
- B4.1Production systems
Check your answers in Augment
A free account opens all 79 questions on Mechanical systems application and selection with their markschemes, and keeps a record of what you have marked.