B3.1 Material selection questions for IB Design Technology

102 questions on Material selection, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of B Design in practice
  • SL and HL

Questions by paper and level

SL and HL questions are for students at either level. HL only questions cover what only HL students study.

PaperSL and HLHL onlyAll
Paper 131114
Paper 2513788
Every paper5448102

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00056Paper 1 · HL only · 1 mark

Figure 4 shows the elastic region of the stress–strain graphs of four polymers, W, X, Y and Z. A designer wants the most flexible of the four for the shock-absorbing bumper of a phone case.

Stress in MPa (0 to 60) against strain in percent (0 to 2). Four straight lines from the origin. At 2 % strain: W reaches 60 MPa, X 40 MPa, Y 20 MPa and Z about 4 MPa.
**Figure 4: Elastic regions of four polymers**

Which polymer should the designer choose?

  1. A

    W

  2. B

    X

  3. C

    Y

  4. D

    Z

Question 2 · DT-00466Paper 2 · HL only · 17 marks

A hospital's manufacturing unit makes patient-specific cranial implants from PEEK, a high-performance thermoplastic, by material extrusion. Each implant is a thin curved shell about 3 mm thick, designed from the patient's CT scan to replace a section of skull. The unit compared a three-axis printer, which prints flat layers, with a five-axis printer, whose bed tilts and rotates so that the layers follow the curve of the shell. For one implant with a mass of 48 g, the three-axis printer used 22 g of support material and the five-axis printer used 3 g. Figure 1 shows the time taken by each stage of production.

Figure 1: stacked bar chart of production time (h) for one implant. Three-axis printer: printing 9, support removal 3, finishing 4, total 16 h. Five-axis printer: printing 11, support removal 0.5, finishing 1.5, total 13 h.
Figure 1: Production time for one cranial implant
  1. (a)

    Using Figure 1, state the total production time for one implant made on the five-axis printer.

    1 mark

  2. (b)

    Calculate the percentage reduction in support material when the five-axis printer is used for the implant.

    2 marks

  3. (c)

    Outline how the movement of the five-axis printer differs from that of the three-axis printer when printing the implant.

    2 marks

  4. (d)

    Explain why reducing support material is particularly important when printing the PEEK cranial implant.

    3 marks

  5. (e)

    Explain how five-axis additive manufacturing affects the strength, surface finish and production time of the cranial implant.

    9 marks

Question 3 · DT-00788Paper 1 · HL only · 1 mark

Figure 1 shows the stress–strain graph from a tensile test on a sample of PETG used as 3D-printing filament.

Stress–strain graph, strain 0 to 13 %, stress 0 to 60 MPa. A straight line from the origin to 40 MPa at 2 % strain, then a curve rising to a peak of 50 MPa at about 7–8 % and falling to fracture at 44 MPa, 12 % strain.
**Figure 1: Stress–strain graph for PETG**

What is the Young's modulus of the PETG?

  1. A

    0.02 GPa

  2. B

    0.63 GPa

  3. C

    2.0 GPa

  4. D

    20 GPa

Question 4 · DT-00467Paper 2 · HL only · 14 marks

The Trekka folding camp stool has three legs made from aluminum alloy tube, which support a triangular polyester fabric seat. The tube is made by extrusion, cut to length and drilled for a central pivot. The three legs are joined at the pivot by a steel rivet, and the legs are anodized. The corners of the seat are stitched into pockets that fit over the ends of the legs. The stool has a mass of 0.6 kg and supports users of up to 110 kg.

  1. (a)

    State the category of manufacturing technique to which the extrusion of the Trekka's aluminum tube belongs.

    1 mark

  2. (b)

    Identify the category of manufacturing technique used for drilling the legs and for riveting the legs of the Trekka stool.

    2 marks

  3. (c)

    Describe how the steel rivet joins the three legs of the Trekka stool at the pivot.

    2 marks

  4. (d)

    Explain why the seat of the Trekka stool is joined to its corner pockets by stitching rather than by an adhesive.

    3 marks

  5. (e)

    Explain two ways in which the properties of aluminum alloy influenced the manufacturing techniques used for the legs of the Trekka stool.

    6 marks

Question 5 · DT-00790Paper 1 · HL only · 1 mark

A backyard zip line has a seat that hangs from a rope. The designer allows for a rider weighing up to 1000 N and uses a safety factor of 6. Four ropes are available.

Rope

Breaking load / kN

Diameter / mm

P

5.5

8

Q

12

12

R

4

6

S

7

9

Which is the thinnest rope that meets the requirement?

  1. A

    P

  2. B

    Q

  3. C

    R

  4. D

    S

Question 6 · DT-00474Paper 2 · 17 marks

Trailhearth is a small company making a skillet (frying pan) for people cooking over campfires and camping stoves. The skillet has a 24 cm cooking surface and a detachable handle with a silicone rubber grip. Hikers want it light enough to carry, but it must survive being placed directly in hot embers. The designers shortlisted three metals for the skillet body, see Table 1. Each body design has a volume of 180 cm³ of metal.

Material

Density / g cm⁻³

Thermal conductivity / W m⁻¹ K⁻¹

Melting point / °C

Behavior in damp storage

Cast iron

7.2

52

1200

rusts unless kept oiled

Aluminum alloy

2.7

160

640

forms a thin protective oxide layer

Stainless steel

7.9

16

1450

does not rust

Table 1: Properties of the shortlisted metals

  1. (a)

    State the material in Table 1 with the lowest density.

    1 mark

  2. (b)

    Calculate how much lighter an aluminum alloy Trailhearth skillet body would be than a cast iron one. Show your working.

    2 marks

  3. (c)

    Outline why the high thermal conductivity of aluminum alloy is an advantage for the Trailhearth skillet.

    2 marks

  4. (d)

    Explain why the handle of the Trailhearth skillet has a silicone rubber grip.

    3 marks

  5. (e)

    Using Table 1, explain how density, melting point and corrosion resistance should be considered when choosing the metal for the Trailhearth skillet body.

    9 marks

Practice all 102 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in practice

  1. B1.1User-centred design
  2. B2.1The design process
  3. B2.2Modelling and prototyping
  4. B3.1Material selectionThis page
  5. B3.2Structural systems application and selectionHL only
  6. B3.3Mechanical systems application and selectionHL only
  7. B3.4Electronic systems application and selectionHL only
  8. B4.1Production systemsHL only

Check your answers in Augment

A free account opens all 102 questions on Material selection with their markschemes, and keeps a record of what you have marked.