B2.1 The design process questions for IB Design Technology

59 questions on The design process, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of B Design in practice
  • SL and HL

Questions by paper and level

SL and HL questions are for students at either level. HL only questions cover what only HL students study.

PaperSL and HLHL onlyAll
Paper 1909
Paper 243750
Every paper52759

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00105Paper 1 · 1 mark

At which point in an iterative design process is a high-fidelity prototype most appropriate?

  1. A

    Exploring many early concepts

  2. B

    Writing the problem statement

  3. C

    Testing a refined design before manufacture

  4. D

    Researching the needs of users

Question 2 · DT-00378Paper 2 · 14 marks

Hopla is designing a folding kick scooter for children aged 5 to 9. To decide which features matter most, it ran an online survey of 240 parents who already own a children's scooter. Each parent chose the one feature they consider most important. The results are shown in Figure 1.

Bar chart, Figure 1: feature parents consider most important, 240 parents. Folds with one hand 84; adjustable handlebar 52; fits in car trunk 46; low weight 38; bright colors 20.
Figure 1: Most important feature chosen by parents (n = 240)

Hopla then held a focus group with eight of the parents and their children.

  1. (a)

    State the feature chosen by the fewest parents in Figure 1.

    1 mark

  2. (b)

    In Figure 1, 84 parents chose "Folds with one hand". Calculate the percentage of the 240 parents who chose this feature as the most important for the Hopla scooter. Show your working.

    2 marks

  3. (c)

    Outline one limitation of the survey as a way of understanding the users of the Hopla scooter.

    2 marks

  4. (d)

    Explain one reason why Hopla held a focus group after the survey.

    3 marks

  5. (e)

    Explain how the survey results and demographic data about the target market could guide the development of the Hopla scooter.

    6 marks

Question 3 · DT-00118Paper 1 · 1 mark

A designer develops a mount for a bicycle light. She moves from paper sketches to a CAD model and then to a 3D-printed model.

Which of the following explain why prototypes in different forms are used during this process?

I. Each form answers different questions about the design
II. Later forms are closer to the final product
III. Feedback from one form informs changes to the next

  1. A

    I and II only

  2. B

    I and III only

  3. C

    II and III only

  4. D

    I, II and III

Question 4 · DT-00384Paper 2 · 16 marks

Dosely is an automatic pill dispenser for older adults who live alone and take several medicines a day. A family member or nurse loads a week of tablets into the dispenser, which then sounds an alarm and opens one compartment at each dose time. The company followed a user-centered design (UCD) process: older adults, family members and community nurses were involved from the first research visits to the final testing of pre-production models.

  1. (a)

    Outline why the Dosely team involved users at the start of the project, before any design solutions were produced.

    2 marks

  2. (b)

    Describe how the Dosely team could evaluate a design solution against the user requirements.

    2 marks

  3. (c)

    Explain one reason why the UCD process used for Dosely is iterative.

    3 marks

  4. (d)

    Explain one disadvantage of using a UCD process to develop the Dosely dispenser.

    3 marks

  5. (e)

    Evaluate the use of UCD to design the Dosely dispenser for older adults with a diverse range of needs and capabilities.

    6 marks

Question 5 · DT-00140Paper 1 · 1 mark

Users testing a children's bicycle helmet report that the buckle is hard to open. The design team changes the CAD model and 3D prints a new buckle overnight, ready for testing the next morning.

Which advantage of rapid prototyping does this best show?

  1. A

    Design changes can be tested in a physical model quickly

  2. B

    It removes the need for further user testing

  3. C

    Printed parts cost less than mass-produced parts

  4. D

    The buckle will be made the same way in production

Question 6 · DT-00468Paper 2 · HL only · 19 marks

Sonnet is developing a charging case for wireless earbuds. The design team began with hand sketches, then built a 3D CAD model. They printed more than 30 base models of the case on an FDM printer, with 0.3 mm layers, to test its size, hinge and magnetic catch. When the design was nearly final, they printed five appearance models by stereolithography (SLA), painted them and showed them to focus groups. The case will be injection molded in polycarbonate, with 200,000 to be made in the first year.

  1. (a)

    State what rapid prototyping uses as its starting point when producing the models of the Sonnet case.

    1 mark

  2. (b)

    Describe how the CAD model of the Sonnet case is prepared before it is printed.

    2 marks

  3. (c)

    Outline one reason why the base models of the Sonnet case were printed with thick 0.3 mm layers rather than thin 0.1 mm layers.

    2 marks

  4. (d)

    Outline why SLA, rather than FDM, was used for the appearance models of the Sonnet case shown to focus groups.

    2 marks

  5. (e)

    Explain why the Sonnet case will not be produced by rapid prototyping techniques.

    3 marks

  6. (f)

    Explain how rapid prototyping supported testing, validation and communication during the development of the Sonnet case.

    9 marks

Practice all 59 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in practice

  1. B1.1User-centred design
  2. B2.1The design processThis page
  3. B2.2Modelling and prototyping
  4. B3.1Material selection
  5. B3.2Structural systems application and selectionHL only
  6. B3.3Mechanical systems application and selectionHL only
  7. B3.4Electronic systems application and selectionHL only
  8. B4.1Production systemsHL only

Check your answers in Augment

A free account opens all 59 questions on The design process with their markschemes, and keeps a record of what you have marked.