C4.1 Design for manufacture strategies questions for IB Design Technology

86 questions on Design for manufacture strategies, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of C Design in context
  • HL only

Questions by paper and level

PaperQuestions
Paper 134
Paper 252
Every paper86

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-01054Paper 1 · 1 mark

A manufacturer redesigns its plastic garden chairs so that they stack inside each other, and three times as many now fit in each shipping container.

Which life-cycle analysis (LCA) stage is most directly improved?

  1. A

    Raw material extraction

  2. B

    Manufacture

  3. C

    Distribution and transport

  4. D

    Disposal and recycling

Question 2 · DT-00404Paper 2 · 16 marks

The Pebble balance bike for children aged 2 to 4 is made from 18 mm birch plywood. Its parts are cut on a CNC router from standard 2440 × 1220 mm sheets. Nesting software arranges the parts for five bikes on each sheet. After cutting, the edges are rounded over and sanded, and the parts are finished with a clear water-based lacquer. The table shows the parts needed for one bike.

Part

Number per bike

Area of each part / m²

Frame side

2

0.160

Fork plate

2

0.045

Seat

1

0.030

  1. (a)

    State what is meant by a subtractive technique.

    1 mark

  2. (b)

    Calculate the percentage of the area of one plywood sheet that is used for the parts of five Pebble bikes. Show your working.

    2 marks

  3. (c)

    Outline one way the nesting software reduces waste when the Pebble parts are cut.

    2 marks

  4. (d)

    Explain one reason why the Pebble parts are cut with a CNC router rather than a laser cutter.

    3 marks

  5. (e)

    Outline why the edges of the Pebble parts are rounded over and sanded before they are lacquered.

    2 marks

  6. (f)

    Explain two reasons why the Pebble balance bike is finished with a clear water-based lacquer.

    6 marks

Question 3 · DT-01097Paper 1 · 1 mark

A teardown of a hairdryer shows that its two housing halves are ultrasonically welded together and its motor is glued in place, so it cannot be opened without damage.

Which strategy would address the weakness found?

  1. A

    Design for process

  2. B

    Design for assembly

  3. C

    Design for disassembly

  4. D

    Inclusive design

Question 4 · DT-00405Paper 2 · 14 marks

The Rondo café chair has a frame made from 22 mm diameter mild steel tube. Each frame is bent from two long lengths of tube on a CNC tube-bending machine, and the two lengths are then MIG welded together. The frame is powder coated, and an injection-molded polypropylene seat is fastened to it with four screws. Rondo chairs are made in batches of 500 for restaurants with outdoor terraces.

  1. (a)

    State one property of mild steel that allows the Rondo frame to be bent without cracking.

    1 mark

  2. (b)

    Describe how the tube for the Rondo frame is bent on the tube-bending machine.

    2 marks

  3. (c)

    Outline one advantage of bending the Rondo frame from long lengths of tube rather than welding it from many short straight pieces.

    2 marks

  4. (d)

    Explain one reason why the seat of the Rondo chair is fastened to the frame with screws rather than adhered.

    3 marks

  5. (e)

    Explain two ways in which powder coating enhances the Rondo chair frame.

    6 marks

Question 5 · DT-01105Paper 1 · 1 mark

Which of the following are the three strategies of design for manufacture (DfM)?

  1. A

    Design for materials, design for process and design for assembly

  2. B

    Design for process, design for assembly and design for disassembly

  3. C

    Design for assembly, design for disassembly and design for recycling

  4. D

    Design for process, design for materials and design for disassembly

Question 6 · DT-00408Paper 2 · 16 marks

Klikbo makes plastic construction bricks for children aged 4 and over. The 2 × 4 brick is injection molded from ABS granules in a steel mold with 8 cavities, so 8 bricks are made in each cycle. Bricks made today must clutch firmly to bricks made many years ago. The chart shows the time taken by each stage of one molding cycle.

Horizontal bar chart of the stages of one molding cycle. Mold close 2 s, injection 2 s, holding pressure 3 s, cooling 9 s, open and eject 2 s.
  1. (a)

    State the stage of the molding cycle for the Klikbo brick that takes the longest time.

    1 mark

  2. (b)

    Calculate the number of Klikbo bricks that one molding machine produces in one hour. Show your working.

    2 marks

  3. (c)

    Describe how injection molding forms a Klikbo brick from ABS granules.

    2 marks

  4. (d)

    Outline one reason why ABS is a suitable material for the Klikbo brick.

    2 marks

  5. (e)

    Explain one reason why injection molding is suited to making Klikbo bricks that fit precisely with bricks made many years earlier.

    3 marks

  6. (f)

    Explain how the design of the Klikbo brick and the design of its mold can reduce the time taken by the cooling stage.

    6 marks

Practice all 86 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in context

  1. C1.1Responsibility of the designer
  2. C1.2Inclusive design
  3. C1.3Beyond usability
  4. C2.1Design for sustainability
  5. C2.2Design for a circular economy
  6. C3.1Product analysis and evaluation
  7. C3.2Life-cycle analysis
  8. C4.1Design for manufacture strategiesThis page

Check your answers in Augment

A free account opens all 86 questions on Design for manufacture strategies with their markschemes, and keeps a record of what you have marked.