- Subjects
- Design Technology
- Question bank
- C2.1 Design for sustainability
C2.1 Design for sustainability questions for IB Design Technology
147 questions on Design for sustainability, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.
- IB Design Technology
- Part of C Design in context
- SL and HL
Questions by paper and level
SL and HL questions are for students at either level. HL only questions cover what only HL students study.
| Paper | SL and HL | HL only | All |
|---|---|---|---|
| Paper 1 | 38 | 10 | 48 |
| Paper 2 | 55 | 44 | 99 |
| Every paper | 93 | 54 | 147 |
Counted on
Questions to try
Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.
The filament bulb in a bicycle light is replaced by an LED with the same light output.
Why does the LED version use less energy?
The Hearth end-grain chopping board is made from small blocks of maple glued together with a waterproof adhesive so that the end grain of each block forms the cutting surface. The glued blank is planed flat, sanded with progressively finer grades of abrasive paper and finished with food-safe mineral oil, followed by a beeswax paste. Owners are advised to re-oil the board once a month.
- (a)
State one reason why a waterproof adhesive is used to join the maple blocks of the Hearth chopping board.
1 mark
- (b)
Outline why the Hearth chopping board is sanded with progressively finer grades of abrasive paper.
2 marks
- (c)
Describe how the mineral oil protects the maple of the Hearth chopping board.
2 marks
- (d)
Outline one reason why the Hearth chopping board is finished with oil and wax rather than a varnish.
2 marks
- (e)
Explain one way in which the oil and wax finish makes the Hearth chopping board easy to maintain.
3 marks
- (f)
Explain two reasons why the Hearth chopping board is made from end-grain blocks glued together rather than from a single piece of solid maple.
6 marks
A firm is choosing between rotational molding a park bench seat from recycled HDPE and fabricating it from steel sheet. Which of the following should influence its choice of manufacturing technique?
I. The number of seats it expects to make
II. The energy used by each process and how each seat can be recycled
III. The material the seat is to be made from
Aerovane makes a fuel manifold for small turbine engines used in business jets. The original manifold was an assembly of 14 nickel alloy parts machined from solid bar and brazed together, with a finished mass of 2.4 kg. The redesigned manifold is a single part made by laser powder bed fusion (PBF). It has a finished mass of 1.7 kg and internal fuel channels that curve around the engine casing. After printing, it is heat treated, its supports are removed and its connecting faces are machined. Figure 1 shows the mass of nickel alloy bought to make one manifold by each method.

- (a)
Using Figure 1, state the mass of nickel alloy bought to make one PBF manifold.
1 mark
- (b)
Using Figure 1, calculate the percentage of the nickel alloy bought for the machined assembly that does not end up in the finished manifold.
2 marks
- (c)
Outline why the curved internal fuel channels of the manifold can be made by PBF but not by machining.
2 marks
- (d)
Outline one reason why the connecting faces of the PBF manifold are machined after printing.
2 marks
- (e)
Explain one disadvantage of using PBF to make the Aerovane manifold.
3 marks
- (f)
Explain how making the manifold by PBF affects its performance in the aircraft, its manufacture and its environmental impact.
9 marks
Plastic drinking straws still do their job, but many cafés have stopped offering them because customers now regard them as unacceptable for the harm they do to the oceans. What type of obsolescence is this?
Stitchback supplies spare parts for vintage sewing machines that are no longer made. Instead of holding stock, it keeps a digital file for each of 1,200 different parts and prints each part when it is ordered, by material extrusion, on a farm of 40 printers. Most parts are small knobs, spool pins and gears printed in nylon or PETG. Each printer runs for 20 hours a day, and an average part takes 2.5 hours to print.
- (a)
List two advantages of material extrusion for producing Stitchback's spare parts.
2 marks
- (b)
Calculate the maximum number of average parts that Stitchback's print farm can produce in one day.
2 marks
- (c)
Outline one reason why printing parts on demand suits Stitchback better than holding stock of injection-molded parts.
2 marks
- (d)
Explain one limitation of a material-extruded nylon gear compared with an injection-molded nylon gear for a Stitchback customer.
3 marks
- (e)
Discuss the environmental impact of Stitchback's approach of printing spare parts on demand.
6 marks
Practice all 147 in Augment
Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.
More questions in Design in context
- C1.1Responsibility of the designer
- C1.2Inclusive design
- C1.3Beyond usabilityHL only
- C2.1Design for sustainabilityThis page
- C2.2Design for a circular economy
- C3.1Product analysis and evaluation
- C3.2Life-cycle analysisHL only
- C4.1Design for manufacture strategiesHL only
Check your answers in Augment
A free account opens all 147 questions on Design for sustainability with their markschemes, and keeps a record of what you have marked.