- Subjects
- Design Technology
- Question bank
- C3.2 Life-cycle analysis
C3.2 Life-cycle analysis questions for IB Design Technology
76 questions on Life-cycle analysis, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.
- IB Design Technology
- Part of C Design in context
- HL only
Questions by paper and level
| Paper | Questions |
|---|---|
| Paper 1 | 34 |
| Paper 2 | 42 |
| Every paper | 76 |
Counted on
Questions to try
Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.
In a cradle-to-grave life-cycle analysis (LCA), which stage is the 'cradle'?
The Peakview action camera is sold in a waterproof housing for divers. The housing is machined from a solid block of 6061 aluminum alloy on a three-axis CNC milling machine, in batches of about 2000 a year. Most of the block is removed as swarf. After milling, the housing is bead blasted (sprayed with fine glass beads) and then anodized black. The table shows the mass of one housing at each stage of milling.
Stage | Mass / g |
|---|---|
Block of aluminum before milling (80 × 60 × 40 mm) | 518 |
After rough milling | 142 |
Finished housing after final milling | 86 |
- (a)
State the mass of aluminum removed from one Peakview housing during final milling.
1 mark
- (b)
Calculate the percentage of the original block's mass that is removed to make one finished Peakview housing. Show your working.
2 marks
- (c)
Describe how milling removes material from the aluminum block to form the Peakview housing.
2 marks
- (d)
Outline one way the swarf from milling the Peakview housings can be prevented from becoming waste.
2 marks
- (e)
Explain one reason why the Peakview housing is milled from solid rather than die cast.
3 marks
- (f)
Explain two reasons why the milled Peakview housing is bead blasted and then anodized.
6 marks
Which of the following is not one of the five stages of a cradle-to-grave life-cycle analysis (LCA)?
The Climbmore climbing frame for school playgrounds is welded from mild steel tube. The designers compared finishes by testing coated steel panels in a salt-spray cabinet, an accelerated test in which panels are kept in a warm salt mist until red rust first appears. The chart shows the results. The designers chose the duplex finish: the welded frame is hot-dip galvanized and then powder coated in bright colors ("Duplex" in the chart).

- (a)
State the time to first red rust for the hot-dip galvanized panel tested for the Climbmore frame.
1 mark
- (b)
Calculate how many times longer the duplex panel resisted red rust than the powder-coated panel. Show your working.
2 marks
- (c)
Describe how the welded Climbmore frame is hot-dip galvanized.
2 marks
- (d)
Explain why the galvanized coating protects the Climbmore frame even where it has been scratched through to the steel.
3 marks
- (e)
Explain how the duplex finish enhances the aesthetics, the durability and the ease of maintenance of the Climbmore climbing frame.
9 marks
In a life-cycle analysis (LCA), in which unit is global warming potential (GWP) usually given?
Aerovane makes a fuel manifold for small turbine engines used in business jets. The original manifold was an assembly of 14 nickel alloy parts machined from solid bar and brazed together, with a finished mass of 2.4 kg. The redesigned manifold is a single part made by laser powder bed fusion (PBF). It has a finished mass of 1.7 kg and internal fuel channels that curve around the engine casing. After printing, it is heat treated, its supports are removed and its connecting faces are machined. Figure 1 shows the mass of nickel alloy bought to make one manifold by each method.

- (a)
Using Figure 1, state the mass of nickel alloy bought to make one PBF manifold.
1 mark
- (b)
Using Figure 1, calculate the percentage of the nickel alloy bought for the machined assembly that does not end up in the finished manifold.
2 marks
- (c)
Outline why the curved internal fuel channels of the manifold can be made by PBF but not by machining.
2 marks
- (d)
Outline one reason why the connecting faces of the PBF manifold are machined after printing.
2 marks
- (e)
Explain one disadvantage of using PBF to make the Aerovane manifold.
3 marks
- (f)
Explain how making the manifold by PBF affects its performance in the aircraft, its manufacture and its environmental impact.
9 marks
Practice all 76 in Augment
Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.
More questions in Design in context
- C1.1Responsibility of the designer
- C1.2Inclusive design
- C1.3Beyond usability
- C2.1Design for sustainability
- C2.2Design for a circular economy
- C3.1Product analysis and evaluation
- C3.2Life-cycle analysisThis page
- C4.1Design for manufacture strategies
Check your answers in Augment
A free account opens all 76 questions on Life-cycle analysis with their markschemes, and keeps a record of what you have marked.