A4.1 Manufacturing techniques questions for IB Design Technology

158 questions on Manufacturing techniques, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of A Design in theory
  • HL only

Questions by paper and level

PaperQuestions
Paper 169
Paper 289
Every paper158

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00321Paper 1 · 1 mark

Which category of manufacturing technique changes the shape of a material without adding or removing any material?

  1. A

    Additive

  2. B

    Subtractive (wasting)

  3. C

    Forming

  4. D

    Finishing

Question 2 · DT-00400Paper 2 · 5 marks

The Gristwell pepper mill has a central spindle made from 6 mm diameter 316 stainless steel bar. The spindles are made on a CNC lathe in batches of 5000. One end of the bar is turned down to a smaller diameter, a thread is cut on the other end, and each spindle is then parted off to length.

  1. (a)

    State the category of manufacturing technique to which turning the Gristwell spindle belongs.

    1 mark

  2. (b)

    Describe how turning reduces the diameter of one end of the Gristwell spindle.

    2 marks

  3. (c)

    Outline one reason why the Gristwell spindle is turned on a CNC lathe rather than a manually operated lathe.

    2 marks

Question 3 · DT-00322Paper 1 · 1 mark

A woodworker makes a spoon by carving a solid block of cherry wood with a knife and gouges. To which category of manufacturing technique does this belong?

  1. A

    Additive

  2. B

    Forming

  3. C

    Joining

  4. D

    Subtractive (wasting)

Question 4 · DT-00401Paper 2 · 5 marks

The Stackit desk organizer is made from five flat parts laser cut from 3 mm cast acrylic sheet. The parts have slots that push together without glue, so the organizer can be sold flat packed.

  1. (a)

    Outline how the laser cutter produces the slots in the Stackit parts.

    2 marks

  2. (b)

    Outline one advantage of laser cutting the Stackit parts rather than cutting them by hand with a saw.

    2 marks

  3. (c)

    State one other sheet material that could be laser cut to make the parts of the Stackit desk organizer.

    1 mark

Question 5 · DT-00323Paper 1 · 1 mark

Which of the following are finishing techniques?

I. Galvanizing
II. Press-forming
III. Polishing

  1. A

    I and II only

  2. B

    I and III only

  3. C

    II and III only

  4. D

    I, II and III

Question 6 · DT-00402Paper 2 · 16 marks

The Peakview action camera is sold in a waterproof housing for divers. The housing is machined from a solid block of 6061 aluminum alloy on a three-axis CNC milling machine, in batches of about 2000 a year. Most of the block is removed as swarf. After milling, the housing is bead blasted (sprayed with fine glass beads) and then anodized black. The table shows the mass of one housing at each stage of milling.

Stage

Mass / g

Block of aluminum before milling (80 × 60 × 40 mm)

518

After rough milling

142

Finished housing after final milling

86

  1. (a)

    State the mass of aluminum removed from one Peakview housing during final milling.

    1 mark

  2. (b)

    Calculate the percentage of the original block's mass that is removed to make one finished Peakview housing. Show your working.

    2 marks

  3. (c)

    Describe how milling removes material from the aluminum block to form the Peakview housing.

    2 marks

  4. (d)

    Outline one way the swarf from milling the Peakview housings can be prevented from becoming waste.

    2 marks

  5. (e)

    Explain one reason why the Peakview housing is milled from solid rather than die cast.

    3 marks

  6. (f)

    Explain two reasons why the milled Peakview housing is bead blasted and then anodized.

    6 marks

Practice all 158 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in theory

  1. A1.1Ergonomics
  2. A2.1User-centred research methods
  3. A2.2Prototyping techniques
  4. A3.1Material classification and properties
  5. A3.2Introduction to structural systems
  6. A3.3Introduction to mechanical systems
  7. A3.4Introduction to electronic systems
  8. A4.1Manufacturing techniquesThis page

Check your answers in Augment

A free account opens all 158 questions on Manufacturing techniques with their markschemes, and keeps a record of what you have marked.