A3.3 Introduction to mechanical systems questions for IB Design Technology

112 questions on Introduction to mechanical systems, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of A Design in theory
  • HL only

Questions by paper and level

PaperQuestions
Paper 155
Paper 257
Every paper112

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00067Paper 1 · 1 mark

A child on a playground swing moves back and forth along the same arc. What type of motion is this?

  1. A

    Linear

  2. B

    Rotary

  3. C

    Oscillating

  4. D

    Reciprocating

Question 2 · DT-00500Paper 2 · 6 marks

The Brisa SM-20 is a domestic sewing machine. An electric motor turns a main shaft that runs along the arm of the machine. A crank on the end of the shaft drives the needle bar up and down through the fabric, while a toothed feed dog under the needle plate pushes the fabric forward a small step after each stitch. A handwheel on the side of the machine lets the user turn the mechanism slowly by hand.

  1. (a)

    State the type of motion of the needle bar of the Brisa SM-20.

    1 mark

  2. (b)

    State the type of motion of the handwheel of the Brisa SM-20.

    1 mark

  3. (c)

    Identify the input and the output of the mechanism that drives the needle bar of the Brisa SM-20.

    2 marks

  4. (d)

    Outline one reason why a handwheel is included on the Brisa SM-20.

    2 marks

Question 3 · DT-00068Paper 1 · 1 mark

The needle of a sewing machine moves up and down along a straight path many times a second. What type of motion does the needle have?

  1. A

    Linear

  2. B

    Rotary

  3. C

    Oscillating

  4. D

    Reciprocating

Question 4 · DT-00501Paper 2 · 6 marks

The Lumo electric toothbrush has a small round brush head that turns back and forth through about 60° instead of spinning all the way round. A DC motor in the handle turns an eccentric pin, which rocks a drive shaft running up the neck of the brush. The motor is powered by a rechargeable battery.

  1. (a)

    State the type of motion of the brush head of the Lumo toothbrush.

    1 mark

  2. (b)

    Outline the difference between the motion of the motor shaft and the motion of the brush head of the Lumo toothbrush.

    2 marks

  3. (c)

    Describe the drive system of the Lumo toothbrush in terms of its input, process and output.

    3 marks

Question 5 · DT-00069Paper 1 · 1 mark

Which of the following move with oscillating motion?

I. The pendulum of a wall clock
II. The blades of a ceiling fan
III. The arm of a windshield wiper

  1. A

    I and II only

  2. B

    I and III only

  3. C

    II and III only

  4. D

    I, II and III

Question 6 · DT-00502Paper 2 · 16 marks

Tallow Toys makes the Hungry Owl, a wooden automaton for children aged 8 and over. Turning a crank handle on the side of a beech-wood box rotates a camshaft inside the box. Four cams on the camshaft move followers that make the owl's head bob, its wings flap and its beak snap shut. The followers are vertical wooden rods that rest on the cams under their own weight. The cams are laser cut from 6 mm birch plywood. Figure 1 shows the four cam profiles, W, X, Y and Z.

Four cam profiles, each with a dot marking the camshaft. W: a round base with one pointed lobe. X: a spiral whose radius grows steadily over one turn, then steps straight back to the smallest radius. Y: a circle with the shaft off its center. Z: an ellipse with the shaft at its center.
Figure 1: The cam profiles of the Hungry Owl. Dots show the camshaft.
  1. (a)

    State the type of motion of the followers in the Hungry Owl.

    1 mark

  2. (b)

    Identify cam X and cam Z in Figure 1.

    2 marks

  3. (c)

    Outline why cam X is suitable for making the owl's beak snap shut.

    2 marks

  4. (d)

    Outline how cam Y produces the bobbing movement of the owl's head.

    2 marks

  5. (e)

    Explain why the crank handle of the Hungry Owl should only be turned in one direction.

    3 marks

  6. (f)

    Explain how child safety and the durability of the mechanism were considered in the design of the Hungry Owl.

    6 marks

Practice all 112 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in theory

  1. A1.1Ergonomics
  2. A2.1User-centred research methods
  3. A2.2Prototyping techniques
  4. A3.1Material classification and properties
  5. A3.2Introduction to structural systems
  6. A3.3Introduction to mechanical systemsThis page
  7. A3.4Introduction to electronic systems
  8. A4.1Manufacturing techniques

Check your answers in Augment

A free account opens all 112 questions on Introduction to mechanical systems with their markschemes, and keeps a record of what you have marked.