A3.4 Introduction to electronic systems questions for IB Design Technology

112 questions on Introduction to electronic systems, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of A Design in theory
  • HL only

Questions by paper and level

PaperQuestions
Paper 139
Paper 273
Every paper112

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00221Paper 1 · 1 mark

An automatic hand dryer has an infrared sensor, a microcontroller, a fan motor and a heating element.

Which of these carries out the process stage of the system?

  1. A

    Infrared sensor

  2. B

    Microcontroller

  3. C

    Fan motor

  4. D

    Heating element

Question 2 · DT-00501Paper 2 · 6 marks

The Lumo electric toothbrush has a small round brush head that turns back and forth through about 60° instead of spinning all the way round. A DC motor in the handle turns an eccentric pin, which rocks a drive shaft running up the neck of the brush. The motor is powered by a rechargeable battery.

  1. (a)

    State the type of motion of the brush head of the Lumo toothbrush.

    1 mark

  2. (b)

    Outline the difference between the motion of the motor shaft and the motion of the brush head of the Lumo toothbrush.

    2 marks

  3. (c)

    Describe the drive system of the Lumo toothbrush in terms of its input, process and output.

    3 marks

Question 3 · DT-00222Paper 1 · 1 mark

Figure 1 shows a system diagram for an aquarium heater that keeps the water at a set temperature.

Figure 1: boxes Temperature sensor, Microcontroller and Heater in a row, joined by arrows P (sensor to microcontroller) and Q (microcontroller to heater). Arrow R runs from Heater to a box Water in tank; arrow S runs from Water in tank back to Temperature sensor.
Figure 1: System diagram of an aquarium heater

Which labeled arrow represents feedback?

  1. A

    P

  2. B

    Q

  3. C

    R

  4. D

    S

Question 4 · DT-00518Paper 2 · 19 marks

The Hearth WR-2 is an emergency radio for use during power cuts. Turning a fold-out crank handle on its side drives a small generator that charges an internal battery. The generator must turn much faster than a person can turn a crank, so the crank drives it through the compound gear train shown in Figure 1.

Plan view of three parallel shafts. The crank shaft carries gear A, 60 teeth, which meshes with gear B, 12 teeth, on the middle shaft. Gear C, 48 teeth, is on the same middle shaft as B and meshes with gear D, 12 teeth, on the generator shaft.
Figure 1: The gear train of the Hearth WR-2 (plan view). Diagram not to scale.
  1. (a)

    Identify the type of gear arrangement formed by gears B and C of the Hearth WR-2.

    1 mark

  2. (b)

    Calculate the number of turns made by gear B of the Hearth WR-2 for one turn of the crank.

    2 marks

  3. (c)

    Outline why the Hearth WR-2 uses a compound gear train rather than a single pair of gears.

    2 marks

  4. (d)

    Outline whether gear D of the Hearth WR-2 turns in the same direction as gear A or in the opposite direction.

    2 marks

  5. (e)

    Describe the Hearth WR-2 charging system in terms of its input, process and output.

    3 marks

  6. (f)

    Explain how user effort, reliability and sustainability were considered in the design of the Hearth WR-2.

    9 marks

Question 5 · DT-00223Paper 1 · 1 mark

Which of the following features help make an electric kettle safe to use?

I. A thermal cut-out that switches the kettle off if it boils dry
II. A double-insulated plastic body
III. A lid that stays locked while the water is boiling

  1. A

    I and II only

  2. B

    I and III only

  3. C

    II and III only

  4. D

    I, II and III

Question 6 · DT-00520Paper 2 · 16 marks

The GlideGate GX is an automatic opener for sliding driveway gates of up to 400 kg. An electric motor in a weatherproof housing beside the gate drives a worm gearbox. A pinion on the output shaft of the gearbox meshes with a galvanized steel rack bolted along the bottom of the gate. A remote control starts the motor, and infrared photocell sensors across the opening stop the gate if a person or car is in the way. If the power fails, the owner unlocks a release lever with a key so that the gate can be pushed by hand.

  1. (a)

    State the type of gear system that moves the gate of the GlideGate GX.

    1 mark

  2. (b)

    Outline why a gearbox is needed between the motor and the pinion of the GlideGate GX.

    2 marks

  3. (c)

    Explain how the GlideGate GX combines gear systems to convert the motion of the motor into the motion of the gate.

    3 marks

  4. (d)

    Outline why the GlideGate GX needs a release lever so that the gate can be pushed by hand when the power fails.

    2 marks

  5. (e)

    Outline one advantage of the self-locking gearbox of the GlideGate GX when the gate is closed.

    2 marks

  6. (f)

    Explain how the safety of users and reliability outdoors were considered in the design of the GlideGate GX.

    6 marks

Practice all 112 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in theory

  1. A1.1Ergonomics
  2. A2.1User-centred research methods
  3. A2.2Prototyping techniques
  4. A3.1Material classification and properties
  5. A3.2Introduction to structural systems
  6. A3.3Introduction to mechanical systems
  7. A3.4Introduction to electronic systemsThis page
  8. A4.1Manufacturing techniques

Check your answers in Augment

A free account opens all 112 questions on Introduction to electronic systems with their markschemes, and keeps a record of what you have marked.