A3.2 Introduction to structural systems questions for IB Design Technology

106 questions on Introduction to structural systems, written by Augment in the style of IB exam papers. Six of them are below in full, to answer on paper.

  • IB Design Technology
  • Part of A Design in theory
  • HL only

Questions by paper and level

PaperQuestions
Paper 154
Paper 252
Every paper106

Counted on

Questions to try

Written by Augment in the style of IB exams, not past papers. Answer them on paper, then check each one against its markscheme with a free account.

Question 1 · DT-00033Paper 1 · 1 mark

Honeycomb in a beehive is made of thin wax walls arranged in hexagonal cells. The same pattern is used for the core of lightweight aircraft floor panels.

What is the main structural benefit of a honeycomb core?

  1. A

    High stiffness for its mass

  2. B

    High surface hardness

  3. C

    High ductility

  4. D

    Low thermal expansion

Question 2 · DT-00489Paper 2 · 15 marks

Lumen Atelier is a small jewelry studio. It makes bangles by bending wire around a steel former by hand, and closes some designs with a spring clasp. The studio tested samples of three wires, P, Q and R, in tension until they broke, see Figure 8.

Simplified stress–strain graph; each line ends where the wire breaks. P: straight to 120 MPa at strain 0.008, then curves up slowly to 210 MPa at strain 0.35. Q: straight to 300 MPa at 0.01, then to 460 MPa at 0.25. R: steepest, straight to 1320 MPa at 0.022, breaks at 1400 MPa at 0.04.
**Figure 8: Simplified stress–strain graph for wires P, Q and R** (not to scale)
  1. (a)

    Using Figure 8, identify the stiffest wire.

    1 mark

  2. (b)

    Using Figure 8, state the stress at which wire Q stops behaving elastically.

    1 mark

  3. (c)

    Using Figure 8, outline which wire is the most ductile.

    2 marks

  4. (d)

    Describe what happens to wire Q if it is loaded to a stress of 400 MPa and the load is then removed.

    2 marks

  5. (e)

    Explain why wire R is suitable for the spring clasp of the Lumen Atelier bangles.

    3 marks

  6. (f)

    Explain how plasticity and elasticity are each important in the design of the Lumen Atelier bangles made from wire P.

    6 marks

Question 3 · DT-00034Paper 1 · 1 mark

The bones in a bird's wing are hollow tubes. A designer copies this idea for the legs of a lightweight walking frame.

Why does a hollow tube resist bending well for its mass?

  1. A

    The air inside the tube carries part of the load

  2. B

    A hollow tube has a higher Young's modulus than a rod

  3. C

    Removing the central material makes the tube more ductile

  4. D

    Its material is far from the center, where bending stress is highest

Question 4 · DT-00492Paper 2 · 14 marks

The Arcline cycle helmet has a thin, curved outer layer of polycarbonate (PC) bonded to a thick liner of expanded polystyrene (EPS) foam, see Figure 9. The PC layer has no separate frame or ribs: its curved form carries loads on its own. In a crash, the EPS liner crushes and does not spring back, so the helmet must be replaced after any serious impact. The helmet has a mass of 260 g.

Cross-section of the Arcline helmet. A thin curved outer layer (PC, 0.5 mm) covers a thick curved liner (EPS, 25 mm), which sits over the dashed outline of the head.
**Figure 9: Cross-section through the Arcline helmet** (not to scale)
  1. (a)

    State the type of structure formed by the outer layer of the Arcline helmet.

    1 mark

  2. (b)

    Outline how the EPS liner reduces the risk of head injury in the Arcline helmet.

    2 marks

  3. (c)

    Outline one mechanical property that makes polycarbonate suitable for the outer layer of the Arcline helmet.

    2 marks

  4. (d)

    Explain why the Arcline helmet combines two materials rather than being made from one.

    3 marks

  5. (e)

    Explain how toughness and density were considered in the design of the Arcline helmet.

    6 marks

Question 5 · DT-00035Paper 1 · 1 mark

Which term describes a structure in which a thin outer skin encloses a space and carries the loads?

  1. A

    Frame structure

  2. B

    Shell structure

  3. C

    Solid structure

  4. D

    Laminated structure

Question 6 · DT-00493Paper 2 · 13 marks

The Rollo folding wheelchair has a chassis of welded metal tubes, with a nylon fabric seat and back slung between them. It folds flat so the user can lift it into a car on their own. It is used indoors and outdoors, in all weather, and is wiped down with disinfectant. The designers are choosing the tube material from Table 4.

Tube material

Density / g cm⁻³

Tensile strength / MPa

Corrosion resistance

Aluminum alloy

2.7

310

good

Titanium alloy

4.4

900

excellent

Chromium–molybdenum steel

7.8

670

poor unless painted

Table 4: Possible tube materials for the Rollo wheelchair

  1. (a)

    State the type of structure used for the tube chassis of the Rollo wheelchair.

    1 mark

  2. (b)

    Outline one advantage of this type of structure for the Rollo wheelchair.

    2 marks

  3. (c)

    Using Table 4, state which tube material has the highest tensile strength.

    1 mark

  4. (d)

    Explain why corrosion resistance is important for the tube material of the Rollo wheelchair.

    3 marks

  5. (e)

    Using Table 4, evaluate the use of titanium alloy instead of aluminum alloy for the tubes of the Rollo wheelchair.

    6 marks

Practice all 106 in Augment

Free with an account. Every question has its markscheme, and Augment keeps the ones you got wrong so you can come back to them.

More questions in Design in theory

  1. A1.1Ergonomics
  2. A2.1User-centred research methods
  3. A2.2Prototyping techniques
  4. A3.1Material classification and properties
  5. A3.2Introduction to structural systemsThis page
  6. A3.3Introduction to mechanical systems
  7. A3.4Introduction to electronic systems
  8. A4.1Manufacturing techniques

Check your answers in Augment

A free account opens all 106 questions on Introduction to structural systems with their markschemes, and keeps a record of what you have marked.